SPL - PERFORMER S800 STEREO POWER AMPLIFIER

$4,290.00

Pay as per month with Paybright

Color
Black
Red
Silver
Quantity

Product Details

Stereo Power Amplifier

This small stereo power amplifier shows everyone that size does not necessarily have anything to do with greatness. With the power of 570 W it has every speaker under control. Thanks to VOLTAiR technology, it is fast, precise and highly efficient with outstanding sound.

Better safe than sorry

The Performer s800 has a protection circuit against DC voltage and a limiter against output overload.

If direct current (DC) is detected, the output stage switches off automatically and the Protect LED lights up red.

To protect the output against overdriving, an LDR limiter (light-dependent resistor) is used. Since it works optically, the audio quality is not affected. The Protect LED lights up yellow when the limiter responds.

As one calls into the forest,

so it echoes out.

This saying inspired us to send the input signal out again in order to drive another power amplifier in bi-amping mode.

Trim to fit

With reference to the s800, “fit” means adapted. And you can adapt the input sensitivity in 0.5 dB steps. From 0 dB to -5.5 dB.

This is the much more audiophile solution for acoustically problematic rooms or loudspeaker set-ups than the panorama potentiometer of the preamplifier.

In addition, the difference in loudness of loudspeakers can be elegantly compensated in bi-amping mode.

Plus & Minus

The loudspeaker binding posts can accommodate banana plugs as well as a stranded wire with a diameter of up to 4mm.

For bi-wiring operation, both types of connection can be used together.

No loudspeaker with less than 4 ohms impedance may be connected.

AMP CTL

The power amplifier can be switched on and off using the AMP CTL connection between the Performer s800 and a preamplifier such as the Director Mk2 or the Crossover.

To do this, connect the 3.5 mm jack sockets with a cable with 3.5 mm mono or stereo jack plugs.

Third-party preamps can also switch the Performer s800 on and off with their 12 V trigger.

Specifications

Analog Input & Thru: XLR (balanced)

Input gain (max)
32.5 dB
Input impedance (THRU not connected)
20 
Common mode rejection (THRU not connected)
-82 dB
Input sensitivity
6 dBu

Loudspeaker Outputs: Binding posts with ø4mm cable hole (screwable) and banana plug

Output power (RMS, 4 Ω)
570 W
Output power (RMS, 8 Ω)
370 W
Harmonic distortion (1 kHz, 8 Ω)
< 0.03 %
Output power (RMS, 8 Ω, Bridge Mode)
450 W
Harmonic distortion (1 kHz, 8 Ω, Bridge Mode)
< 0.011 %
Output power (peak to peak)
74 V
Output power (peak to peak, Bridge Mode)
180 V
Output voltage (RMS)
35 V
Output voltage (RMS, Bridge Mode)
86 V
Output impedance (20 Hz – 20 kHz)
< 0.031 Ω
Output impedance (20 Hz – 20 kHz, Bridge Mode)
< 0.043 Ω
Amplification gain
26 dB
Amplification gain (Bridge Mode)
32 dB
Damping factor (1 kHz, 8 Ohm)
> 300
Damping factor (1 kHz, 8 Ohm, Bridge Mode)
> 190
Frequency range (-3dB)
9 Hz – 200 kHz
Noise (A-weighted)
-123 dBu

Internal Linear Power Supply with Shielded Toroidal Transformer

Toroidal transformer
875 VA
Operating voltage (Input stage)
+/- 60 V
Operating voltage (power stage)
+/- 60 V
Operating voltage for relays, LEDs, AMP CTL
+ 12 V

Mains Power Supply

Mains voltage (selectable, see fuse chamber)
230 V AC / 50; 115 V AC / 60 Hz
Fuse 230 V
T 4 A
Fuse 115 V
T 8 A
Power consumption
max. 875 VA
Idle power consumption
40 W
Stand-by power consumption
< 0.3 W

Dimensions & Weight

W x H x D (width x height incl. feet x depth)
278 x 100 x 342 mm
11 x 8 x 13.47 inch
Unit weight
12.8 kg
28.2 lbs
Shipping weight
14 kg
30.9 lbs

Referenz: 0 dBu = 0,775V. Technische Änderungen vorbehalten.

View More